ball valve (open/close)Multi-Voltage ModelVoltage 24-240 VAC / VDC (-0/+5%) 50 / 60HzTwo auxiliary limit switchesManual overrideVisual position indicatorIndicator lights for operating statusWorking temperature: -20°C at + 60°CDegree of protection IEC 60529: IP-67Internal heater to prevent damage from condensation 3.5WHousing in polyamide (humidity max. 75%)Fastening and main shaft made of stainless steelRunning time /90°: 50mm 9s, 63mm 13sOperating time without load (s/90°) +-10%Power consumption at maximum torque: 24VAC/VDC 1.3A 30.7W; 240VAC/VDC 0.2A 46WInstallation and operating instructions are available electronically for downloadNote when using our solar controller: If the motor valve and additional pump are operated in the solar circuit at the same time, please use a relay with two switching contacts for this operating mode (article number ELECTRICREL2)!The housing color may vary!
ball valve (open/close)Multi-Voltage ModelVoltage 24-240 VAC / VDC (-0/+5%) 50 / 60HzTwo auxiliary limit switchesManual overrideVisual position indicatorIndicator lights for operating statusWorking temperature: -20°C at + 60°CDegree of protection IEC 60529: IP-67Internal heater to prevent damage from condensation 3.5WHousing in polyamide (humidity max. 75%)Fastening and main shaft made of stainless steelRunning time /90°: 50mm 9s, 63mm 13sOperating time without load (s/90°) +-10%Power consumption at maximum torque: 24VAC/VDC 1.3A 30.7W; 240VAC/VDC 0.2A 46WInstallation and operating instructions are available electronically for downloadNote when using our solar controller: If the motor valve and additional pump are operated in the solar circuit at the same time, please use a relay with two switching contacts for this operating mode (article number ELECTRICREL2)!The housing color may vary!
L ballMulti-Voltage ModelVoltage 24-240 VAC / VDC (-0/+5%) 50 / 60HzTwo auxiliary limit switchesManual overrideVisual position indicatorIndicator lights for operating statusWorking temperature: -20°C at + 60°CDegree of protection IEC 60529: IP-67Internal heater to prevent damage from condensation 3.5WHousing in polyamide (humidity max. 75%)Fastening and main shaft made of stainless steelRunning time /90°: 50mm 9s, 63mm 13sOperating time without load (s/90°) +-10%Power consumption at maximum torque: 24VAC/VDC 1.3A 30.7W; 240VAC/VDC 0.2A 46WInstallation and operating instructions are available electronically for downloadNote when using our solar controller: If the motor valve and additional pump are operated in the solar circuit at the same time, please use a relay with two switching contacts for this operating mode (article number ELECTRICREL2)!The housing color may vary!
L ballMulti-Voltage ModelVoltage 24-240 VAC / VDC (-0/+5%) 50 / 60HzTwo auxiliary limit switchesManual overrideVisual position indicatorIndicator lights for operating statusWorking temperature: -20°C at + 60°CDegree of protection IEC 60529: IP-67Internal heater to prevent damage from condensation 3.5WHousing in polyamide (humidity max. 75%)Fastening and main shaft made of stainless steelRunning time /90°: 50mm 9s, 63mm 13sOperating time without load (s/90°) +-10%Power consumption at maximum torque: 24VAC/VDC 1.3A 30.7W; 240VAC/VDC 0.2A 46WInstallation and operating instructions are available electronically for downloadNote when using our solar controller: If the motor valve and additional pump are operated in the solar circuit at the same time, please use a relay with two switching contacts for this operating mode (article number ELECTRICREL2)!The housing color may vary!
Connection variant:
Connection sleeve required on both sides
Installed horizontally for drainage, installed vertically for ventilation. Ideal for connecting a garden hose to fill the SOLAR-RIPP ® system during commissioning. Gluing not possible! Variant for butt welding or heating element welding as well as a mixed variant available.
End 1: Outer diameter 50mm PVC adhesive socket. Inner diameter 40mm PVC adhesive sleeve (on pipe) for gluing to PVC-U fittings or pipes.End 2: Hose connection for flexible 50mm connection sleeve with two clamps (on SOLAR-RIPP ® distributor/collector or RIPPultimate solar absorber).
Best professional quality, ductile - therefore almost indestructible, frost-proof, black, extra UV-resistant PE-HD material, polyethylene, polyethylene, 50mm outside diameter, weldable (gluing is NOT possible), 3mm wall thickness, illustration as an example.
Multi-part connection set to connect a RIPPultimate ® or SOLAR-RIPP ® solar surface to a pipeline made of corrugated hose. The individual parts are not yet glued together. Please select your desired diameter (corrugated hose dimension). The diameter refers to the inside diameter of the smooth corrugated hose sections.
Easy-to-install, flexible corrugated hose made of heat-resistant, high-quality polypropylene (PP) with high UV resistance, can be cut every 1.5m, outer diameter approx. 45mm, inner diameter at the smooth connecting sleeves min. 38mm, black, 25.5m roll.
50mm installation adapter made of PVC-U for mounting a SOLAR-RIPP ® temperature sensor with 6mm diameter as a cold water sensor for measuring the pool water sucked in by the swimming pool pump, corrosion-free, the use of the optionally available thermal paste to increase contact is recommended, simply glue into a T-fitting with 50mm PVC-U inner diameter.
1-1/2" (48.3mm) installation adapter made of PVC-U for mounting a SOLAR-RIPP ® temperature sensor with 6mm diameter as a cold water sensor for measuring the pool water sucked in by the swimming pool pump, corrosion-free, the use of the optionally available thermal paste to increase contact is recommended, simply glue into a T-fitting with a British imperial 1-1/2" (48.3mm) PVC-U inner diameter.
T ballMulti-Voltage ModelVoltage 24-240 VAC / VDC (-0/+5%) 50 / 60HzTwo auxiliary limit switchesManual overrideVisual position indicatorIndicator lights for operating statusWorking temperature: -20°C at + 60°CDegree of protection IEC 60529: IP-67Internal heater to prevent damage from condensation 3.5WHousing in polyamide (humidity max. 75%)Fastening and main shaft made of stainless steelRunning time /90°: 50mm 9s, 63mm 13sOperating time without load (s/90°) +-10%Power consumption at maximum torque: 24VAC/VDC 1.3A 30.7W; 240VAC/VDC 0.2A 46WInstallation and operating instructions are available electronically for downloadNote when using our solar controller: If the motor valve and additional pump are operated in the solar circuit at the same time, please use a relay with two switching contacts for this operating mode (article number ELECTRICREL2)!The housing color may vary!
T ballMulti-Voltage ModelVoltage 24-240 VAC / VDC (-0/+5%) 50 / 60HzTwo auxiliary limit switchesManual overrideVisual position indicatorIndicator lights for operating statusWorking temperature: -20°C at + 60°CDegree of protection IEC 60529: IP-67Internal heater to prevent damage from condensation 3.5WHousing in polyamide (humidity max. 75%)Fastening and main shaft made of stainless steelRunning time /90°: 50mm 9s, 63mm 13sOperating time without load (s/90°) +-10%Power consumption at maximum torque: 24VAC/VDC 1.3A 30.7W; 240VAC/VDC 0.2A 46WInstallation and operating instructions are available electronically for downloadNote when using our solar controller: If the motor valve and additional pump are operated in the solar circuit at the same time, please use a relay with two switching contacts for this operating mode (article number ELECTRICREL2)!The housing color may vary!
Slightly flexible connection sleeve with 50mm inner diameter. Made from material pressure-resistant up to 3 bar including two corrosion-protected metal clamps. High chemical resistance! 80mm long. Other lengths available on request!
Slightly flexible connection sleeve with 50mm inner diameter. Made from material pressure-resistant up to 3 bar including two corrosion-protected metal clamps. High chemical resistance! 150mm long. Other lengths available on request!
Flexible connection coupling to connect an original SOLAR-RIPP ® solar absorber to a 50mm pipe system. The rubberized transition sleeve has an inner diameter of 50mm and has two corrosion-resistant metal hose clamps. This component can also be used to connect original SOLAR-RIPP ® distributors and collectors with an outer diameter of 50mm.
Best professional quality, ductile - therefore almost indestructible, frost-proof, black, extra UV-resistant PE-HD material, polyethylene, polyethylene, 50mm outside diameter, weldable (gluing is NOT possible), 3mm wall thickness, illustration as an example.
Best professional quality, ductile - therefore almost indestructible, frost-proof, black, extra UV-resistant PE-HD material, polyethylene, polyethylene, 50mm outside diameter, weldable (gluing is NOT possible), 3mm wall thickness, illustration as an example.
PVC-U sleeve with double-sided adhesive sleeve. One side 50mm inner diameter, the other side has 1-1/2" (1.5"), 48.3mm, BI (British Imperial) inner diameter, grey
Very stable pipe fastening (16mm thick) for screwing 50mm pipes made of e.g. PE-HD or PVC-U to walls, ceilings, masonry, wooden posts etc. (gluing not possible), black, stable plastic suitable for outdoor use with centrally arranged hole for 6mm screws (can be drilled out if necessary), 25mm distance (space between pipe and mounting level), base area (screw-on contact surface) 16mm x 49mm, at the widest point the clamp is 59mm wide on the outside, almost indestructible, recommended installation distance for PE pipe 75cm (at pressure level SDR11). Two-part with removable clip bracket. NOT suitable for original SOLAR-RIPP ® distributors and collectors (clamp is too wide), please use our narrower metal clamps for this!
PE-HD connection set for incorporating the cold water sensor installation adapter made of PVC-U into a 50mm HD-PE pipe, please install in front of the pump (suction side) in order to measure the pool water temperature as accurately as possible, black/grey, illustration for example.
